Today morning was getting lil tired of even my inside tank hitting 30 C mark, So i realised that 1 fan was not able to cope up in the peak hrs.
I had 2 CPU Heat sink fan lying with me. I like them as they have faster speed and are slim profile. Earlier i had mounted them using a mirror clip, but today i realised that i can do without any thing.
I simply cut out a small section in existing frame and that became my inbuilt hang on.
Small saw blade and flat filler did the job for me.
Using CPU Heat Sink Fans
-
- Aspiring Star of AquapetZ!
- Posts: 1156
- Joined: Tue Oct 11, 2011 4:27 pm
- Location: New Delhi
Using CPU Heat Sink Fans
You do not have the required permissions to view the files attached to this post.
- SCORPIO
- Site Admin
- Posts: 10376
- Joined: Tue Oct 04, 2011 11:01 am
- Location: Delhi, India
- Contact:
Re: Using CPU Heat Sink Fans
Nice. But I think vibration will displace the fan from its position.
“Take up one idea. Make that one idea your life - think of it, dream of it, live on that idea. This is the way to success.”
...................Swami Vivekananda
...................Swami Vivekananda
- Romi
- Editor
- Posts: 2726
- Joined: Thu Oct 13, 2011 2:50 pm
- Location: North Delhi, NCR.
- Contact:
Re: Using CPU Heat Sink Fans
Very nice, Syed. Are they completely steady and secure in their place?
-
- Aspiring Star of AquapetZ!
- Posts: 1156
- Joined: Tue Oct 11, 2011 4:27 pm
- Location: New Delhi
Re: Using CPU Heat Sink Fans
It is snug fit and the vibration from these fans is very low.
I first cut the gap lil less than the glass thickness and then i filed it to snug fit. Also these fans are very light there is no weight issue also.
they were running full time, no issue in the fitting till now
I first cut the gap lil less than the glass thickness and then i filed it to snug fit. Also these fans are very light there is no weight issue also.
they were running full time, no issue in the fitting till now
- nikhil_julka
- Rising Star of AquaPetZ!
- Posts: 111
- Joined: Thu Jan 10, 2013 6:00 pm
- Contact:
Re: Using CPU Heat Sink Fans
syed.ali wrote:It is snug fit and the vibration from these fans is very low.
I first cut the gap lil less than the glass thickness and then i filed it to snug fit. Also these fans are very light there is no weight issue also.
they were running full time, no issue in the fitting till now
good job
Is the result satisfactory?
How much does these cost or should cost?
I am also looking for the same fans and heard they cant be used with the power adaptors?
"Facing truth is a momentary difficulty but lifetime easy to live with"
Nikhil Julka
M: +91 9711116308
http://www.whatslocaltoday.com
-
- Aspiring Star of AquapetZ!
- Posts: 1156
- Joined: Tue Oct 11, 2011 4:27 pm
- Location: New Delhi
Re: Using CPU Heat Sink Fans
Thanks.nikhil_julka wrote: good job
Is the result satisfactory?
How much does these cost or should cost?
I am also looking for the same fans and heard they cant be used with the power adaptors?
Yep the result is satisfactory earlier i have only single fan and that one was not able to fight alone in this high heat, the temp was going above 30, now with these 2 add on, i am good, the temp is back in 25-27 range.
I got them along with the heat sink from Junk seller in Nehru place, i think paid 50 or 80 each.
They are running on 12 volt adaptors you can see the details of the adaptor on http://aquapetz.com/viewtopic.php?f=32& ... d&start=20
- Matrix
- Rising Star of AquaPetZ!
- Posts: 274
- Joined: Sun Oct 30, 2011 10:18 pm
- Location: Noida/Nashik
Re: Using CPU Heat Sink Fans
keeping them in either corners will also help, that way you can get two side support for the fan.
---
Amol
Amol
-
- Aspiring Star of AquapetZ!
- Posts: 1156
- Joined: Tue Oct 11, 2011 4:27 pm
- Location: New Delhi
Re: Using CPU Heat Sink Fans
Not really possible bro as sides are thin, so wall is barely think enough to cut it to hook and also get support from side, I might have to do another diy for corner support, will look into that.Matrix wrote:keeping them in either corners will also help, that way you can get two side support for the fan.